Hello!
The Linux-sound list appears to be dead (I don't see my message in
http://www.kernelnotes.org/lnxlists/linux-sound/), so I'm sending to the
authors and the people discussing the problem on the linux-kernel mailing
list.
An additional problem is that opl3 cannot find the device unless I load
and unload the old driver (ymf_sb). Probably the new driver should put the
OPL3 interface to the legacy mode if it cannot handle it directly.
This confirms my point that you should not disable building both drivers
as modules at this stage.
Regards,
Pavel Roskin
---------- Forwarded message ----------
Date: Tue, 5 Dec 2000 19:26:34 -0500 (EST)
From: Pavel Roskin <proski@gnu.org>
To: linux-sound@vger.kernel.org
Subject: YMF PCI - thanks, glitches, patches
Hello!
The native YMF PCI driver from Linux-2.4.0-test12-pre5 works on my card:
Dec 5 18:07:11 fonzie kernel: ymfpci0: YMF740C at 0xf0000000 IRQ 10
Dec 5 18:07:11 fonzie kernel: ac97_codec: AC97 Audio codec, id:
0x4144:0x5303 (Unknown)
Thanks to everybody who made it!
Now about problems. Sometimes I get such messages in the log:
Dec 5 18:08:16 fonzie kernel: ymfpci: ioctl cmd 0x5401
Dec 5 18:08:50 fonzie last message repeated 9 times
While playing some sounds I'm getting
$ play spinout.wav
sox: Unable to set audio speed to 5512 (set to 8000)
$ file spinout.wav
spinout.wav: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 8 bit,
mono 5512 Hz
This always happens for some sounds, and never happens for others. This
message doesn't appear with the old driver (ymf_sb). I'm attaching
spinout.wav.
The next problem is the configuration file, linux/drivers/sound/Config.in.
I'm sending you a patch that fixes the following problems:
1) The new driver does not depend (directly or indirectly) on the OSS
sound.o module, thus CONFIG_SOUND_YMFPCI should not depend on
CONFIG_SOUND_OSS.
2) CONFIG_SOUND_YMFPCI should depend on CONFIG_PCI. You cannot compile the
driver without PCI support.
3) Both drivers (native and legacy) should disable the other driver if
eigther of them is to be compiled into the kernel. However, it should be
possible to compile both drivers as modules. I did it so I can compare
them.
4) Don't forget about spaces in the description.
You may also want to add a dependency to CONFIG_EXPERIMENTAL for
CONFIG_SOUND_YMFPCI (not in my patch) if you feel that the driver is not
ready for everybody. Just writing (EXPERIMENTAL) doesn't disable the
question about the driver when CONFIG_EXPERIMENTAL is not set.
The patch also contains minimal descriptions for CONFIG_SOUND_YMPCI and
CONFIG_SOUND_YMFPCI. I hope somebody will add more stuff there.
By the way, I'm surprised why many drivers for PCI sound cards don't
depend on CONFIG_PCI.
Regards,
Pavel Roskin
_______________________
--- linux/Documentation/Configure.help Tue Dec 5 10:08:10 2000
+++ linux/Documentation/Configure.help Tue Dec 5 17:57:26 2000
@@ -14250,6 +14250,18 @@
If unsure, say Y.
+Yamaha PCI native mode support (EXPERIMENTAL)
+CONFIG_SOUND_YMFPCI
+ This is an experimental driver that uses Yamaha PCI sound cards in
+ the native mode. You may also want to try another driver,
+ "Yamaha PCI legacy mode support" under the OSS drivers.
+
+Yamaha PCI legacy mode support
+CONFIG_SOUND_YMPCI
+ This is a driver for Yamaha PCI sound cards that turns them
+ to the Sound Blaster compatible mode. You don't need to enable
+ Sound Blaster support to use it.
+
ACI mixer (miroPCM12/PCM20)
CONFIG_SOUND_ACI_MIXER
ACI (Audio Command Interface) is a protocol used to communicate with
--- linux/drivers/sound/Config.in Tue Dec 5 10:08:13 2000
+++ linux/drivers/sound/Config.in Tue Dec 5 17:59:30 2000
@@ -79,6 +79,9 @@
fi
dep_tristate ' VIA 82C686 Audio Codec' CONFIG_SOUND_VIA82CXXX $CONFIG_PCI
+if [ "$CONFIG_SOUND_YMPCI" != "y" ]; then
+ dep_tristate ' Yamaha PCI native mode support (EXPERIMENTAL)' CONFIG_SOUND_YMFPCI $CONFIG_SOUND $CONFIG_PCI
+fi
dep_tristate ' OSS sound modules' CONFIG_SOUND_OSS $CONFIG_SOUND
@@ -142,9 +145,8 @@
dep_tristate ' Yamaha FM synthesizer (YM3812/OPL-3) support' CONFIG_SOUND_YM3812 $CONFIG_SOUND_OSS
dep_tristate ' Yamaha OPL3-SA1 audio controller' CONFIG_SOUND_OPL3SA1 $CONFIG_SOUND_OSS
dep_tristate ' Yamaha OPL3-SA2, SA3, and SAx based PnP cards' CONFIG_SOUND_OPL3SA2 $CONFIG_SOUND_OSS
- dep_tristate ' Yamaha PCI legacy mode support' CONFIG_SOUND_YMPCI $CONFIG_SOUND_OSS $CONFIG_PCI
- if [ "$CONFIG_SOUND_YMPCI" = "n" ]; then
- dep_tristate 'Yamaha PCI native mode support (EXPERIMENTAL)' CONFIG_SOUND_YMFPCI $CONFIG_SOUND_OSS
+ if [ "$CONFIG_SOUND_YMFPCI" != "y" ]; then
+ dep_tristate ' Yamaha PCI legacy mode support' CONFIG_SOUND_YMPCI $CONFIG_SOUND_OSS $CONFIG_PCI
fi
dep_tristate ' 6850 UART support' CONFIG_SOUND_UART6850 $CONFIG_SOUND_OSS
_______________________
This archive was generated by hypermail 2b29 : Thu Dec 07 2000 - 21:00:15 EST