So I'm trying to get the Promise Fasttrack 100 driver included
with 2.4.0-test10 to work on my system.
I have 2 45GB drives hooked up in RAID0.
I'm trying to install directly onto the drives, but I'm having
a couple problems.
It seems to detect the controller card and the drives, but
they are not assigned to any devices.
Any suggestions?
Thanks,
--James Lamanna
Here is some info:
dmesg:
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PDC20265: IDE controller on PCI bus 00 dev 88
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
ide0: BM-DMA at 0x6400-0x6407, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x6408-0x640f, BIOS settings: hdc:DMA, hdd:pio
PDC20267: IDE controller on PCI bus 00 dev 58
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
PDC20267: neither IDE port enabled (BIOS)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This line is interesting I thought...
/proc/pci:
Bus 0, device 11, function 0:
RAID bus controller: Promise Technology, Inc. 20267 (rev 2).
IRQ 10.
Master Capable. Latency=32.
I/O at 0x9400 [0x9407].
I/O at 0x9000 [0x9003].
I/O at 0x8800 [0x8807].
I/O at 0x8400 [0x8403].
I/O at 0x8000 [0x803f].
Non-prefetchable 32 bit memory at 0xd5000000 [0xd501ffff].
Bus 0, device 17, function 0:
Unknown mass storage controller: Promise Technology, Inc. 20265 (rev
2).
IRQ 10.
Master Capable. Latency=32.
I/O at 0x7800 [0x7807].
I/O at 0x7400 [0x7403].
I/O at 0x7000 [0x7007].
I/O at 0x6800 [0x6803].
I/O at 0x6400 [0x643f].
Non-prefetchable 32 bit memory at 0xd4800000 [0xd481ffff].
/proc/ide/pdc202xx:
PDC20265 Chipset.
------------------------------- General Status
Burst Mode : enabled
Host Mode : Normal
Bus Clocking : 33 PCI Internal
IO pad select : 10 mA
Status Polling Period : 5
Interrupt Check Status Polling Delay : 7
--------------- Primary Channel ---------------- Secondary Channel
-------------
enabled enabled
66 Clocking disabled disabled
Mode PCI Mode PCI
FIFO Empty FIFO Empty
--------------- drive0 --------- drive1 -------- drive0 ----------
drive1 ------
DMA enabled: no no yes no
DMA Mode: NOTSET NOTSET NOTSET
NOTSET
PIO Mode: NOTSET NOTSET NOTSET
NOTSET
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu Nov 30 2000 - 21:00:19 EST