This patch, against 2.4.0-test9-pre2, moves ethtool.h from the private
domain of the sparc ports into include/linux. This publishes an
existing interface, and has been discussed before. (search past lkml
subject headers for "media tool" and "ethtool")
This updated patch should take some of the past threads into account.
The differences from the current sparc ethtool.h are:
* bitmask for advertising as well as supported media types
* interrupt mitigation hints max{tx,rx}pkt (Jes suggestion)
* four reserved u32 slots for future expansion
* assigned an ioctl: SIOCETHTOOL (0x8944)
Questions, comments, and feedback welcome. If there are no objections,
I'll submit to DaveM for inclusion in 2.4.0-test9-whatever, after this
current round of discussion.
Jeff
diff -urN vanilla/linux-2.4.0-test9-pre2/include/linux/ethtool.h linux_2_3/include/linux/ethtool.h
--- vanilla/linux-2.4.0-test9-pre2/include/linux/ethtool.h Wed Dec 31 19:00:00 1969
+++ linux_2_3/include/linux/ethtool.h Sun Sep 17 17:29:10 2000
@@ -0,0 +1,96 @@
+/* $Id: ethtool.h,v 1.1.186.1 2000/09/16 20:13:14 jgarzik Exp $
+ * ethtool.h: Defines for Linux ethtool.
+ *
+ * Copyright (C) 1998 David S. Miller (davem@redhat.com)
+ */
+
+#ifndef _LINUX_ETHTOOL_H
+#define _LINUX_ETHTOOL_H
+
+
+/* This should work for both 32 and 64 bit userland. */
+struct ethtool_cmd {
+ u32 cmd;
+ u32 supported; /* Features this interface supports */
+ u32 advertising; /* Features this interface advertises */
+ u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */
+ u8 duplex; /* Duplex, half or full */
+ u8 port; /* Which connector port */
+ u8 phy_address;
+ u8 transceiver; /* Which tranceiver to use */
+ u8 autoneg; /* Enable or disable autonegotiation */
+ u32 maxtxpkt; /* Tx pkts before generating tx int */
+ u32 maxrxpkt; /* Rx pkts before generating rx int */
+ u32 reserved[4];
+};
+
+
+/* CMDs currently supported */
+#define ETHTOOL_GSET 0x00000001 /* Get settings, non-privileged. */
+#define ETHTOOL_SSET 0x00000002 /* Set settings, privileged. */
+
+/* compatibility with older code */
+#define SPARC_ETH_GSET ETHTOOL_GSET
+#define SPARC_ETH_SSET ETHTOOL_SSET
+
+/* Indicates what features are supported by the interface. */
+#define SUPPORTED_10baseT_Half (1 << 0)
+#define SUPPORTED_10baseT_Full (1 << 1)
+#define SUPPORTED_100baseT_Half (1 << 2)
+#define SUPPORTED_100baseT_Full (1 << 3)
+#define SUPPORTED_1000baseT_Half (1 << 4)
+#define SUPPORTED_1000baseT_Full (1 << 5)
+#define SUPPORTED_Autoneg (1 << 6)
+#define SUPPORTED_TP (1 << 7)
+#define SUPPORTED_AUI (1 << 8)
+#define SUPPORTED_MII (1 << 9)
+#define SUPPORTED_FIBRE (1 << 10)
+
+/* Indicates what features are advertised by the interface. */
+#define ADVERTISED_10baseT_Half (1 << 0)
+#define ADVERTISED_10baseT_Full (1 << 1)
+#define ADVERTISED_100baseT_Half (1 << 2)
+#define ADVERTISED_100baseT_Full (1 << 3)
+#define ADVERTISED_1000baseT_Half (1 << 4)
+#define ADVERTISED_1000baseT_Full (1 << 5)
+#define ADVERTISED_Autoneg (1 << 6)
+#define ADVERTISED_TP (1 << 7)
+#define ADVERTISED_AUI (1 << 8)
+#define ADVERTISED_MII (1 << 9)
+#define ADVERTISED_FIBRE (1 << 10)
+
+/* The following are all involved in forcing a particular link
+ * mode for the device for setting things. When getting the
+ * devices settings, these indicate the current mode and whether
+ * it was foced up into this mode or autonegotiated.
+ */
+
+/* The forced speed, 10Mb, 100Mb, gigabit. */
+#define SPEED_10 10
+#define SPEED_100 100
+#define SPEED_1000 1000
+
+/* Duplex, half or full. */
+#define DUPLEX_HALF 0x00
+#define DUPLEX_FULL 0x01
+
+/* Which connector port. */
+#define PORT_TP 0x00
+#define PORT_AUI 0x01
+#define PORT_MII 0x02
+#define PORT_FIBRE 0x03
+
+/* Which tranceiver to use. */
+#define XCVR_INTERNAL 0x00
+#define XCVR_EXTERNAL 0x01
+#define XCVR_DUMMY1 0x02
+#define XCVR_DUMMY2 0x03
+#define XCVR_DUMMY3 0x04
+
+/* Enable or disable autonegotiation. If this is set to enable,
+ * the forced link modes above are completely ignored.
+ */
+#define AUTONEG_DISABLE 0x00
+#define AUTONEG_ENABLE 0x01
+
+#endif /* _LINUX_ETHTOOL_H */
diff -urN vanilla/linux-2.4.0-test9-pre2/drivers/net/sunhme.c linux_2_3/drivers/net/sunhme.c
--- vanilla/linux-2.4.0-test9-pre2/drivers/net/sunhme.c Thu Sep 7 11:32:00 2000
+++ linux_2_3/drivers/net/sunhme.c Sun Sep 17 17:29:03 2000
@@ -24,6 +24,7 @@
#include <linux/string.h>
#include <linux/delay.h>
#include <linux/init.h>
+#include <linux/ethtool.h>
#include <asm/system.h>
#include <asm/bitops.h>
#include <asm/io.h>
@@ -41,7 +42,6 @@
#ifndef __sparc_v9__
#include <asm/io-unit.h>
#endif
-#include <asm/ethtool.h>
#include <asm/uaccess.h>
#include <linux/netdevice.h>
diff -urN vanilla/linux-2.4.0-test9-pre2/include/asm-sparc/ethtool.h linux_2_3/include/asm-sparc/ethtool.h
--- vanilla/linux-2.4.0-test9-pre2/include/asm-sparc/ethtool.h Tue Feb 1 02:37:19 2000
+++ linux_2_3/include/asm-sparc/ethtool.h Wed Dec 31 19:00:00 1969
@@ -1,79 +0,0 @@
-/* $Id: ethtool.h,v 1.2 2000/01/31 04:59:17 davem Exp $
- * ethtool.h: Defines for SparcLinux ethtool.
- *
- * Copyright (C) 1998 David S. Miller (davem@redhat.com)
- */
-
-#ifndef _SPARC_ETHTOOL_H
-#define _SPARC_ETHTOOL_H
-
-/* We do things like this so it does not matter what kernel
- * headers you have on your system etc.
- */
-#undef SIOCETHTOOL
-#define SIOCETHTOOL (SIOCDEVPRIVATE + 0x0f)
-
-/* This should work for both 32 and 64 bit userland. */
-struct ethtool_cmd {
- u32 cmd;
- u32 supported;
- u16 speed;
- u8 duplex;
- u8 port;
- u8 phy_address;
- u8 transceiver;
- u8 autoneg;
-};
-
-/* CMDs currently supported */
-#define SPARC_ETH_GSET 0x00000001 /* Get settings, non-privileged. */
-#define SPARC_ETH_SSET 0x00000002 /* Set settings, privileged. */
-
-/* Indicates what features are supported by the interface. */
-#define SUPPORTED_10baseT_Half 0x00000001
-#define SUPPORTED_10baseT_Full 0x00000002
-#define SUPPORTED_100baseT_Half 0x00000004
-#define SUPPORTED_100baseT_Full 0x00000008
-#define SUPPORTED_1000baseT_Half 0x00000010
-#define SUPPORTED_1000baseT_Full 0x00000020
-#define SUPPORTED_Autoneg 0x00000040
-#define SUPPORTED_TP 0x00000080
-#define SUPPORTED_AUI 0x00000100
-#define SUPPORTED_MII 0x00000200
-#define SUPPORTED_FIBRE 0x00000400
-
-/* The following are all involved in forcing a particular link
- * mode for the device for setting things. When getting the
- * devices settings, these indicate the current mode and whether
- * it was foced up into this mode or autonegotiated.
- */
-
-/* The forced speec, 10Mb, 100Mb, gigabit. */
-#define SPEED_10 10
-#define SPEED_100 100
-#define SPEED_1000 1000
-
-/* Duplex, half or full. */
-#define DUPLEX_HALF 0x00
-#define DUPLEX_FULL 0x01
-
-/* Which connector port. */
-#define PORT_TP 0x00
-#define PORT_AUI 0x01
-#define PORT_MII 0x02
-#define PORT_FIBRE 0x03
-
-/* Which tranceiver to use. */
-#define XCVR_INTERNAL 0x00
-#define XCVR_EXTERNAL 0x01
-#define XCVR_DUMMY1 0x02
-#define XCVR_DUMMY2 0x03
-#define XCVR_DUMMY3 0x04
-
-/* Enable or disable autonegotiation. If this is set to enable,
- * the forced link modes above are completely ignored.
- */
-#define AUTONEG_DISABLE 0x00
-#define AUTONEG_ENABLE 0x01
-
-#endif /* _SPARC_ETHTOOL_H */
diff -urN vanilla/linux-2.4.0-test9-pre2/include/asm-sparc64/ethtool.h linux_2_3/include/asm-sparc64/ethtool.h
--- vanilla/linux-2.4.0-test9-pre2/include/asm-sparc64/ethtool.h Tue Feb 1 02:37:19 2000
+++ linux_2_3/include/asm-sparc64/ethtool.h Wed Dec 31 19:00:00 1969
@@ -1,79 +0,0 @@
-/* $Id: ethtool.h,v 1.2 2000/01/31 04:59:19 davem Exp $
- * ethtool.h: Defines for SparcLinux ethtool.
- *
- * Copyright (C) 1998 David S. Miller (davem@redhat.com)
- */
-
-#ifndef _SPARC64_ETHTOOL_H
-#define _SPARC64_ETHTOOL_H
-
-/* We do things like this so it does not matter what kernel
- * headers you have on your system etc.
- */
-#undef SIOCETHTOOL
-#define SIOCETHTOOL (SIOCDEVPRIVATE + 0x0f)
-
-/* This should work for both 32 and 64 bit userland. */
-struct ethtool_cmd {
- u32 cmd;
- u32 supported;
- u16 speed;
- u8 duplex;
- u8 port;
- u8 phy_address;
- u8 transceiver;
- u8 autoneg;
-};
-
-/* CMDs currently supported */
-#define SPARC_ETH_GSET 0x00000001 /* Get settings, non-privileged. */
-#define SPARC_ETH_SSET 0x00000002 /* Set settings, privileged. */
-
-/* Indicates what features are supported by the interface. */
-#define SUPPORTED_10baseT_Half 0x00000001
-#define SUPPORTED_10baseT_Full 0x00000002
-#define SUPPORTED_100baseT_Half 0x00000004
-#define SUPPORTED_100baseT_Full 0x00000008
-#define SUPPORTED_1000baseT_Half 0x00000010
-#define SUPPORTED_1000baseT_Full 0x00000020
-#define SUPPORTED_Autoneg 0x00000040
-#define SUPPORTED_TP 0x00000080
-#define SUPPORTED_AUI 0x00000100
-#define SUPPORTED_MII 0x00000200
-#define SUPPORTED_FIBRE 0x00000400
-
-/* The following are all involved in forcing a particular link
- * mode for the device for setting things. When getting the
- * devices settings, these indicate the current mode and whether
- * it was foced up into this mode or autonegotiated.
- */
-
-/* The forced speec, 10Mb, 100Mb, gigabit. */
-#define SPEED_10 10
-#define SPEED_100 100
-#define SPEED_1000 1000
-
-/* Duplex, half or full. */
-#define DUPLEX_HALF 0x00
-#define DUPLEX_FULL 0x01
-
-/* Which connector port. */
-#define PORT_TP 0x00
-#define PORT_AUI 0x01
-#define PORT_MII 0x02
-#define PORT_FIBRE 0x03
-
-/* Which tranceiver to use. */
-#define XCVR_INTERNAL 0x00
-#define XCVR_EXTERNAL 0x01
-#define XCVR_DUMMY1 0x02
-#define XCVR_DUMMY2 0x03
-#define XCVR_DUMMY3 0x04
-
-/* Enable or disable autonegotiation. If this is set to enable,
- * the forced link modes above are completely ignored.
- */
-#define AUTONEG_DISABLE 0x00
-#define AUTONEG_ENABLE 0x01
-
-#endif /* _SPARC64_ETHTOOL_H */
diff -urN vanilla/linux-2.4.0-test9-pre2/include/linux/sockios.h linux_2_3/include/linux/sockios.h
--- vanilla/linux-2.4.0-test9-pre2/include/linux/sockios.h Sat Jan 22 14:54:57 2000
+++ linux_2_3/include/linux/sockios.h Sun Sep 17 17:29:10 2000
@@ -71,7 +71,7 @@
#define SIOCGIFTXQLEN 0x8942 /* Get the tx queue length */
#define SIOCSIFTXQLEN 0x8943 /* Set the tx queue length */
-
+#define SIOCETHTOOL 0x8944 /* Ethtool interface */
/* ARP cache control calls. */
/* 0x8950 - 0x8952 * obsolete calls, don't re-use */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Sep 23 2000 - 21:00:16 EST