Hi,
I've compiled about 10 various kernels so I have some additional
information. IDE patches upto ide.2.2.16 (dd. 2000-06-15) solve the
problem with ht6560a, but newer patches starting ide.2.2.16.20000619
not.
So Andre, what may be the cause? What was so special on your patches
till 15-Jun-2000? I did a diff between these versions and it has
almost 200KB, so I'm not able to guess what difference is fatal.
On 15 Jul 2000, at 13:37, Petr Soucek wrote:
> my 486 box with Holtek HT6560A ide vlb controller works only with 2.2
> kernel with Andre Hedrick's patches - I tested 2.2.15 and 2.2.17pre4
> and both work fine.
>
> But 2.2.17pre4, 2.2.12 (Redhat), 2.3.99pre6, 2.4.0-test2 ends with
> the same error during reading partition table:
>
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 50MHz system bus speed for PIO modes; override with
> idebus=xx
> hda: WDC AC24300L, ATA DISK drive
> hdb: WDC AC36400L, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: 8421840 sectors (4312 MB) w/256KiB Cache, CHS=557/240/63
> hdb: 12594960 sectors (6449 MB) w/256KiB Cache, CHS=833/240/63
> Partition check:
> hda:hda: status timeout: status=0xff { Busy }
> hda: drive not ready for command
> ide0: reset timed-out, status=0xff
> hda: status timeout: status=0xff { Busy }
> hda: drive not ready for command
> ide0: reset timed-out, status=0xff
> hda: status timeout: status=0xff { Busy }
> end_request: I/O error, dev 03:00 (hda), sector 0
> hda: drive not ready for command
> unable to read partition table
> hdb:hdb: status timeout: status=0xff { Busy }
> hdb: drive not ready for command
> ide0: reset timed-out, status=0xff
> hdb: status timeout: status=0xff { Busy }
> hdb: drive not ready for command
> ide0: reset timed-out, status=0xff
> hdb: status timeout: status=0xff { Busy }
> end_request: I/O error, dev 03:40 (hdb), sector 0
> hdb: drive not ready for command
> unable to read partition table
>
> (the same behavior both with and without ide0=ht6560b)
>
> With Andre's patches both disks works fine, but there is another
> problem, false "ports already in use":
>
> Uniform Multi-Platform E-IDE driver Revision: 6.30
> ide: Assuming 50MHz system bus speed for PIO modes; override with
> idebus=xx
> hda: WDC AC24300L, ATA DISK drive
> hdb: WDC AC36400L, ATA DISK drive
> ide1: ports already in use, skipping probe
> ide2: ports already in use, skipping probe
> ide3: ports already in use, skipping probe
> ide4: ports already in use, skipping probe
> ide5: ports already in use, skipping probe
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: WDC AC24300L, 4112MB w/256kB Cache, CHS=557/240/63
> hdb: WDC AC36400L, 6149MB w/256kB Cache, CHS=833/240/63
> .... other devices initialization
> Partition check:
> sda: sda1 sda2 sda3
> hda: [PTBL] [524/255/63] hda1 hda2 < hda5 >
> hdb: [PTBL] [784/255/63] hdb1 hdb2 < hdb5 >
>
> For completeness, this is clean 2.2.17pre4 kernel:
>
> hda: WDC AC24300L, ATA DISK drive
> hdb: WDC AC36400L, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: WDC AC24300L, 4112MB w/256kB Cache, CHS=557/240/63
> hdb: WDC AC36400L, 6149MB w/256kB Cache, CHS=833/240/63
> .....
>
> Partition check:
> sda: sda1 sda2 sda3
> hda:hda: status timeout: status=0xff { Busy }
> hda: drive not ready for command
> ide0: reset timed-out, status=0xff
> hda: status timeout: status=0xff { Busy }
> hda: drive not ready for command
> ide0: reset timed-out, status=0xff
> hda: status timeout: status=0xff { Busy }
> end_request: I/O error, dev 03:00 (hda), sector 0
> hda: drive not ready for command
> unable to read partition table
> hdb:hdb: status timeout: status=0xff { Busy }
> hdb: drive not ready for command
> ide0: reset timed-out, status=0xff
> hdb: status timeout: status=0xff { Busy }
> hdb: drive not ready for command
> ide0: reset timed-out, status=0xff
> hdb: status timeout: status=0xff { Busy }
> end_request: I/O error, dev 03:40 (hdb), sector 0
> hdb: drive not ready for command
> unable to read partition table
>
> It seems the wrong behavior was fixed in ide-2.2..... patches, but
> not in both 2.2. and 2.4 mainstream kernel.
>
> Best Regards,
>
>
> Petr Soucek
> Ryston Electronics s.r.o
> petr@ryston.cz http://www.ryston.cz/
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.rutgers.edu
> Please read the FAQ at http://www.tux.org/lkml/
Petr Soucek
Ryston Electronics s.r.o.
Modranska 621/72
CZ-143 00 Praha 4, Czech Republic
tel +420-2-61302222 fax +420-2-61302211
Email: petr@ryston.cz http://www.ryston.cz
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Jul 15 2000 - 21:00:22 EST