Hi,
We had a kernel panic. ksymoops said:
-------
ksymoops 0.7c on i686 2.2.14. Options used
-v /root/vmlinux (specified)
-K (specified)
-L (specified)
-O (specified)
-M (specified)
Unable to handle kernel paging request at virtual address 0000217b
current->tss.cr3 = 0b9e9000, %cr3 = 0b9e9000
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c015f1d6>]
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010282
eax: 0000217b ebx: c1081d20 ecx: d69ea114 edx: d69ea114
esi: ca3740b0 edi: c1081d20 ebp: d0a21e30 esp: d0a21e1c
ds: 0018 es: 0018 ss: 0018
Process ban_pub.pl (pid: 8178, process nr: 86, stackpage=d0a21000)
Stack: 00000218 d69ea114 d3f0cf20 c014e4d1 d3f0cf20 ca374000 c015f51f ca374000
c1081d20 00000218 ca374000 ca3740b0 ca374054 ca374000 c015f645 ca374000
c1081d20 ca3740b0 c1081402 0000000e c015ca35 ca374000 ca3740b0 ca374000
Call Trace: [<c014e4d1>] [<c015f51f>] [<c015f645>] [<c015ca35>] [<c015dd91>] [<c016281b>] [<c0162bb6>]
[<c0155ed6>] [<c01561bd>] [<c014fcfd>] [<c0117811>] [<c010a097>] [<c0109d64>]
Code: 83 38 01 0f 95 c0 25 ff 00 00 00 85 c0 0f 85 a2 01 00 00 8b
>>EIP; c015f1d6 <tcp_retrans_try_collapse+46/208> <=====
Trace; c014e4d1 <__kfree_skb+a1/a8>
Trace; c015f51f <tcp_retransmit_skb+a3/164>
Trace; c015f645 <tcp_xmit_retransmit_queue+65/e4>
Trace; c015ca35 <tcp_ack+289/370>
Trace; c015dd91 <tcp_rcv_established+449/5e8>
Trace; c016281b <tcp_v4_do_rcv+37/124>
Trace; c0162bb6 <tcp_v4_rcv+2ae/334>
Trace; c0155ed6 <ip_local_deliver+16a/1b8>
Trace; c01561bd <ip_rcv+299/2c8>
Trace; c014fcfd <net_bh+179/1d4>
Trace; c0117811 <do_bottom_half+45/64>
Trace; c010a097 <do_IRQ+3b/40>
Trace; c0109d64 <common_interrupt+18/20>
Code; c015f1d6 <tcp_retrans_try_collapse+46/208>
00000000 <_EIP>:
Code; c015f1d6 <tcp_retrans_try_collapse+46/208> <=====
0: 83 38 01 cmpl $0x1,(%eax) <=====
Code; c015f1d9 <tcp_retrans_try_collapse+49/208>
3: 0f 95 c0 setne %al
Code; c015f1dc <tcp_retrans_try_collapse+4c/208>
6: 25 ff 00 00 00 and $0xff,%eax
Code; c015f1e1 <tcp_retrans_try_collapse+51/208>
b: 85 c0 test %eax,%eax
Code; c015f1e3 <tcp_retrans_try_collapse+53/208>
d: 0f 85 a2 01 00 00 jne 1b5 <_EIP+0x1b5> c015f38b <tcp_retrans_try_collapse+1fb/208>
Code; c015f1e9 <tcp_retrans_try_collapse+59/208>
13: 8b 00 mov (%eax),%eax
Aiee, killing interrupt handler
-------
dmesg:
-------
Linux version 2.2.14 (root@ns1.ovh.net) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #2 lun mai 1 15:47:20 CEST
2000
Detected 501143455 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 499.71 BogoMIPS
Memory: 387628k/393152k available (980k kernel code, 412k reserved, 4092k data, 40k init)
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k)
Page cache hash table entries: 131072 (order 7, 512k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium III (Katmai) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xf08b0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with<4>keyboard: Too many NACKs -- noisy kbd cable?
keyboard: Too many NACKs -- noisy kbd cable?
no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DPTA-371360, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: IBM-DPTA-371360, 13042MB w/1961kB Cache, CHS=1662/255/63, UDMA
floppy0: no floppy controllers found
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid1 personality registered
(scsi0) <Adaptec AHA-294X Ultra2 SCSI host adapter> found at PCI 12/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 385 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.21/3.2.4
<Adaptec AHA-294X Ultra2 SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 80.0 Mbyte/sec, offset 31.
Vendor: IBM Model: DNES-309170W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 80.0 Mbyte/sec, offset 31.
Vendor: IBM Model: DNES-309170W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xd000, 00:01:02:06:d0:58, IRQ 10
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
MII transceiver found at address 0, status 786d.
Enabling bus-master transmits and whole-frame receives.
Partition check:
sda: sda1
sdb: sdb1
md.c: sizeof(mdp_super_t) = 4096
hda: hda1 hda2 < hda5 hda6 hda7 >
autodetecting RAID arrays
(read) sda1's sb offset: 8956096 [events: 00000041]
(read) sdb1's sb offset: 8956096 [events: 00000041]
autorun ...
considering sdb1 ...
adding sdb1 ...
adding sda1 ...
created md0
bind<sda1,1>
bind<sdb1,2>
running: <sdb1><sda1>
now!
sdb1's event counter: 00000041
sda1's event counter: 00000041
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 128k
md0: 1 data-disks, max readahead per data-disk: 128k
raid1: device sdb1 operational as mirror 1
raid1: device sda1 operational as mirror 0
raid1: raid set md0 not clean; reconstructing mirrors
raid1: raid set md0 active with 2 out of 2 mirrors
md: updating md0 RAID superblock on device
sdb1 [events: 00000042](write) sdb1's sb offset: 8956096
md: syncing RAID array md0
md: minimum _guaranteed_ reconstruction speed: 100 KB/sec.
md: using maximum available idle IO bandwith for reconstruction.
md: using 128k window.
sda1 [events: 00000042](write) sda1's sb offset: 8956096
.
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 40k freed
Adding Swap: 393552k swap-space (priority -1)
md: md0: sync done.
-------
-- Amicalement, oCtAvEConnexion terminée par expiration du délai d'attente
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun May 07 2000 - 21:00:21 EST