[1.] One line summary of the problem:
I receive errors while reading the last track of an audio cd with 2.3.X
[2.] Full description of the problem/report:
Following is the output from cdda2wav under 2.3.X kernels. This is a
continuing problem with 2.3.47 and later versions. This does not happen
with 2.2.14 and earlier. It always gets to 99 percent, then shows an
error. It happens on all audio CDs I've tested.
[root@wr5z rw1]# cdda2wav -B -D/dev/cdrom -Ocdr -t14 track14
cdrom device (/dev/cdrom) is not of type generic SCSI. Setting interface
to cooked_ioctl.
724992 bytes buffer memory requested, 4 buffers, 75 sectors
#Cdda2wav version 1.8_linux_2.2.14-1.2.0_i686_i686 real time sched.
soundcard support
scsi0: ERROR on channel 0, id 0, lun 0, CDB: Request Sense 00 00 00 40
00
[valid=0] Info fld=0x0, Current sd0b:00: sense key Medium Error
Additional sense indicates No seek complete
I/O error: dev 0b:00, sector 945248
cannot read sector: Input/output error
AUDIOtrack pre-emphasis copy-permitted tracktype channels
1-14 no yes audio 2
DATAtrack recorded copy-permitted tracktype
15-15 uninterrupted yes data
Table of Contents: total tracks:15, (total time 73:05.37)
1.( 3:58.07), 2.( 3:27.10), 3.( 3:54.68), 4.( 3:03.60), 5.(
4:05.37)
6.( 4:04.68), 7.( 3:11.65), 8.( 2:54.30), 9.( 3:12.10), 10.(
3:44.57)
11.( 3:43.55), 12.( 3:21.45), 13.( 3:23.13), 14.| 3:51.61|,
15.[23:05.51]
Table of Contents: starting sectors
1.( 0), 2.( 17857), 3.( 33392), 4.( 51010), 5.(
64795)
6.( 83207), 7.( 101575), 8.( 115965), 9.( 129045), 10.(
143455)
11.( 160312), 12.( 177092), 13.( 192212), 14.( 207450), 15.(
236311)
lead-out( 328762)
CDINDEX discid: XZOGxA.rldXW9JJwFnTXseGn_pw-
CDDB discid: 0xc9111f0f
CD-Text: not detected
CD-Extra: detected
samplefile size will be 40891872 bytes.
recording 231.08133 seconds stereo with 16 bits @ 44100.0 Hz
->'track14'...
overlap:min/max/cur, jitter, percent_done:
1/ 1/ 1/ 0 99%can't read frame #224766 (error 671088640).
1/ 2/ 1/ 2352 99% track 14 successfully recorded
1/ 2/13/9999999 100%[root@wr5z rw1]#
[3.] Keywords (i.e., modules, networking, kernel):
audio, cdrom, kernel
[4.] Kernel version (from /proc/version):
[root@wr5z linux]# cat /proc/version
Linux version 2.3.99-pre6-5 (root@wr5z) (gcc version egcs-2.91.66
19990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 24 12:44:15 CDT 2000
[5.] Output of Oops.. message N/A
[6.] A small shell script N/A
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
[root@wr5z linux]# sh scripts/ver_linux
-- Versions installed: (if some fields are empty or look
-- unusual then possibly you have very old versions)
Linux wr5z 2.3.99-pre6-5 #1 Mon Apr 24 12:44:15 CDT 2000 i586 unknown
Kernel modules 2.3.10-pre1
Gnu C egcs-2.91.66
Binutils 2.9.1.0.24
Linux C Library 2.1.2
Dynamic linker ldd (GNU libc) 2.1.2
Procps 2.0.4
Mount 2.9u
Net-tools 1.53
Console-tools 1999.03.02
Sh-utils 2.0
Modules Loaded opl3
[7.2.] Processor information (from /proc/cpuinfo):
[root@wr5z linux]# cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 5
model : 8
model name : AMD-K6(tm) 3D processor
stepping : 12
cpu MHz : 451.040545
cache size : 64 KB
fdiv_bug : no
hlt_bug : no
sep_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr mce cx8 sep mtrr pge mmx 3dnow
bogomips : 897.84
[7.3.] Module information (from /proc/modules):
[root@wr5z linux]# cat /proc/modules
opl3 11932 0 (unused)
[7.4.] Loaded driver and hardware information (/proc/ioports,
/proc/iomem)
[root@wr5z linux]# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0220-022f : soundblaster
02f8-02ff : serial(auto)
0376-0376 : ide1
0388-038b : Yamaha OPL3
03bc-03be : parport0
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial(auto)
d000-dfff : PCI Bus #01
d000-d0ff : ATI Technologies Inc 3D Rage Pro AGP 1X/2X
e000-e00f : VIA Technologies, Inc. VT82C586 IDE [Apollo]
e000-e007 : ide0
e008-e00f : ide1
e800-e87f : Digital Equipment Corporation DECchip 21041 [Tulip Pass 3]
e800-e87f : eth0
ec00-ec3f : 3Com Corporation 3c900 10BaseT [Boomerang]
ec00-ec3f : eth1
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: VIA Technologies, Inc. VT82C597 [Apollo VP3] (rev
03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 16 set
Region 0: Memory at e0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=7 SBA+ 64bit- FW- Rate=1
Command: RQ=7 SBA+ AGP- 64bit- FW- Rate=1
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e4000000-e7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586 ISA [Apollo VP] (rev
41)
Subsystem: Unknown device 1106:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
06) (prog-if 8a)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at e000
00:07.3 Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:08.0 Ethernet controller: Digital Equipment Corporation DECchip 21041
[Tulip Pass 3] (rev 21)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800
Region 1: Memory at ea000000 (32-bit, non-prefetchable)
00:0a.0 Ethernet controller: 3Com Corporation 3c900 10BaseT [Boomerang]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 3 min, 8 max, 64 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ec00
01:00.0 VGA compatible controller: ATI Technologies Inc 215GB [Mach64
GB] (rev 5c)
Subsystem: Unknown device 1002:0084
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 64 set, cache line size 08
Region 0: Memory at e4000000 (32-bit, non-prefetchable)
Region 1: I/O ports at d000
Region 2: Memory at e6000000 (32-bit, non-prefetchable)
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=21
Command: RQ=255 SBA+ AGP- 64bit- FW- Rate=21
[7.6.] SCSI information (from /proc/scsi/scsi)
[root@wr5z linux]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: Model: 40X CD-ROM Rev: 4.3A
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: PHILIPS Model: CDD3610 CD-R/RW Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
[X.] Other notes, patches, fixes, workarounds:
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Apr 30 2000 - 21:00:08 EST