hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } 2.2.15pre4

From: Douglas F.Elznic (dfelznic@syr.edu)
Date: Tue Jan 25 2000 - 19:58:55 EST

I have been getting the following errors since I upgraded to 2.2.15pre4.
I do not think that I configured anything different this time around. I can not
figure out what if there is something in particular that causes this error.

hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: DMA disabled
hdb: DMA disabled
ide0: reset: success:

I am running:
Linux calvert 2.2.15pre4 #2 Mon Jan 24 18:02:46 EST 2000 i686 unknown
Kernel modules 2.1.121
Gnu C 2.95.2
Binutils 2.9.5.0.16
Linux C Library 2.1.2
Dynamic linker ldd (GNU libc) 2.1.2
Procps 2.0.6
Mount 2.9y
Net-tools 1.53
Console-tools 0.2.2
Sh-utils 2.0
Modules Loaded vfat fat
With hda and hdb being:
[root@calvert linux]# hdparm -vi /dev/hda

/dev/hda:
 multcount = 0 (off)
 I/O support = 0 (default 16-bit)
 unmaskirq = 0 (off)
 using_dma = 0 (off)
 keepsettings = 0 (off)
 nowerr = 0 (off)
 readonly = 0 (off)
 readahead = 8 (on)
 geometry = 1401/255/63, sectors = 22510656, start = 0
 
 Model=Maxtor 91152D8, FwRev=WAS82739, SerialNo=K806FPDA
 Config={ Fixed }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=29
 BuffType=3(DualPortCache), BuffSize=256kB, MaxMultSect=16, MultSect=off
 DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
 
 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
 UDMA modes: mode0 mode1 *mode2
 Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4
 
[root@calvert linux]# hdparm -vi /dev/hdb
 
/dev/hdb:
 multcount = 0 (off)
 I/O support = 0 (default 16-bit)
 unmaskirq = 0 (off)
 using_dma = 0 (off)
 keepsettings = 0 (off)
 nowerr = 0 (off)
 readonly = 0 (off)
 readahead = 8 (on)
 geometry = 3739/255/63, sectors = 60074784, start = 0
 
 Model=WDC WD307AA, FwRev=05.05B05, SerialNo=WD-WMA111025946
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
 BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
 DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=60074784
 WARNING 43560720 ORPHANED SECTORS :: KERNEL REPORTING ERROR
 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
 UDMA modes: mode0 mode1 *mode2 mode3 mode4
 Drive Supports : ATA-1 ATA-2 ATA-3 ATA-4
                              
lspci reports my ide controller being a:
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
        Flags: bus master, medium devsel, latency 64
        I/O ports at 1000

     -- 

--
Douglas F. Elznic
<dfelznic @ syr.edu>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/

This archive was generated by hypermail 2b29 : Mon Jan 31 2000 - 21:00:16 EST